3SAE EndFace Prep Station II

EndFace Prep Station



Large diameter optical fibers are increasingly important in the development of new optical technologies. Cleaving these fibers for presents many challenges, more so as the fiber diameter increases. Low angle offsets and smooth, flat endfaces are required. Many fibers are non-round or have internal structures that interfere with conventional cleaving. With some fibers priced in hundreds of dollars per meter, the length of cutoff scrap must be minimized.

The 3SAE EndFace Prep Station meets these challenges with a novel, polishing-based design that now features both flat and angle polishing. The results are consistent, even for shaped fibers. The endfaces are flat and highly polished. The EPS is not an adapted connector polisher – it is a purpose-built LD fiber preparation unit optimized for splicing and other large diameter fiber termination applications.

Choose from a selection of standard programs, or create and store a custom program for a specific fiber. Selectable programs ensure repeatable performance and the bright, clear LCD screen guides the user with the correct action for each step. No special skill or “touch” is required –the EPS’s precision fixturing holds the fibers precisely, and the automated system lowers the fibers smoothly onto the adjustable-speed polishing plate.

A filtered-air final cleaning/drying system is used to dry the fiber after cleaning in the included 3SAE Ultrasonic Cleaner. The 3SAE Ultrasonic Cleaner is a purpose-built ultrasonic fiber cleaner that was designed specifically for fiber applications. Many years of splicing experience went into the functional, ergonomic design that ensures consistent cleaning results. When the preparation process is complete, the fiber endfaces are flat, low-angle, and ready for splicing. Less than 2 mm of scrap length means less wasted expensive fiber and allows more accurate placement of splices and components.

EndFace Prep Station Chart


Product Fea


tures

> Angled polishing capabilities

> Lowest available cleave angles

> Less than 2mm scrap fiber waste

> No additional fiber handling system required

> Operator independent

> Easy handling

> No PC required

> High first pass yield

>No PC required

>High first pass yield

 

Technical Specs

> Dimensions: 299.7 (W) x 292 (D) x 223.5 (H) mm

> Power Source: External Supply 24 V

> Compressed Air: Max 95 psi., 0.6 SCMF

> Fiber Cladding: 400-2000 μm*

> Cleave Angle: Typical < 0.30°

> Angle Cleaving: Up to 15° of rotation (from vertical).

> Cycle Time: Typically 1-3 minutes
*Fibers >1000 μm require custom fiber holders, not included.

 


Standard Package and Accessories


Product Part Number Qty
EPS Series II
CLV-01-0011  
Power Supply
SPT-10-0846 1
Power Cord
FPU-02-0037 1
User’s Manual
N/A 1
350 μm EPS II Single Fiber Holder
SPT-01-0381  
550 μm EPS II Single Fiber Holder SPT-01-0382  
750 μm EPS II Single Fiber Holder
SPT-01-0383  
1000 μm EPS II Single Fiber Holder
SPT-01-0384  
2000 μm EPS II Single Fiber Holder
SPT-01-0385  
*Custom fiber holder available upon request    
3SAE Ultrasonic Cleaner
ACC-01-0001 1
Power Supply
SPT-01-1243 1
SS Polishing Disc
SPT-01-0241 4
Diamond Polishing Papers
N/A 12
Weights
N/A 1
4mm to 1/4 inch NPT Adaptor
SPT-10-0395 1
Air Line 6 feet at 4mm
N/A 1
Optional Components
   
30um Diamond Lapping Film
SPT-10-0473  
9um Diamond Lapping Film
SPT-10-0474  
3um Diamond Lapping Film
SPT-10-0475  

1um Diamond Lapping Film

SPT-10-0476  
50 g Weight
SPT-01-0198  
100 g Weight
SPT-01-0199  
SS Polishing Disc SPT-01-0241  
Air Filter SPT-10-0008  

Downloads

>>Download Product Information Sheet